Page 1 of 1
Yet more questions about cutting dubs...
Posted: Tue Feb 02, 2010 4:39 pm
by bobby_dozen
Before everyone shouts at me, I've searched through everything I could find on here and DOA and I tried PMing Jason a week ago and emailing Transition but I've had no reply as of yet... Here's a copy of the email I sent:
After debating it for about 3 years and re-reading everything on the forum about them, I think I'm finally going to take the plunge and cut some dubs. I was wondering as I'm based in Leamington Spa is there any way I could book a time to come and attend the session to perhaps learn a bit about mixdowns etc. Also does that cost more?
As an aside is there also a way of hearing the differences between PVC and Acetate dubs, even though I'm sold on the latter? Even on the internet as MP3 clips (although I guess this makes little sense)?
Oh and finally, do you get a CD of the audio that goes to the cutter or is that extra, assuming that you slightly master the intial mixdown? Could I just record the acetate when it's new in case it wears out too much, so I still have the slightly mastered (and warm) sounding copy of the tune. How much and in what way would this recording differ from the signal sent to the cutter?
Sorry for bombarding you for so many questions, I couldn't find good answers to them on the forum already.
If anyone has any answers, it would be much appreciated as I really want to get them cut but just want to find out a little bit more about what exactly I'm going to be paying all that money for. That doesn't seem unreasonable does it?
Re: Yet more questions about cutting dubs...
Posted: Tue Feb 02, 2010 10:28 pm
by prisoner
maybe try calling down to Transition directly.
http://www.transition-studios.com/contact.html
I imagine with the influx of people interested in these sorts of things their inboxs are filling up and it's probably hard to weed through who's serious and who's wasting their time.
Re: Yet more questions about cutting dubs...
Posted: Tue Feb 02, 2010 11:04 pm
by pete
bobby_dozen wrote:I think I'm finally going to take the plunge and cut some dubs.
Good decision.
bobby_dozen wrote:Is there also a way of hearing the differences between PVC and Acetate dubs, even though I'm sold on the latter?
There is a slight difference, which is hardly noticeable in the club. I prefer PVC plates as they last much longer and the cue points don't wear out that much. Also you will carry less weight with them.
bobby_dozen wrote:Could I just record the acetate when it's new in case it wears out too much, so I still have the slightly mastered (and warm) sounding copy of the tune. How much and in what way would this recording differ from the signal sent to the cutter?
It is possible to record the fresh plate, makes sense if you have good needles and a nice converter. Definitely makes a big difference to the original file, in the end it is exactly what the dubplate sounds like, and that is all the reason you are cutting it, right?
Re: Yet more questions about cutting dubs...
Posted: Tue Feb 02, 2010 11:08 pm
by bobby_dozen
Cheers for the info pete. @prisoner, I'll try calling them this week and see what happens.
Edit: The tune in my sig is one of the tunes I'm going to cut, anyone have any comments on how well it'll translate? Does it need drastic changes? I've played it out a couple of times off CD and it sounded OK but it was pretty difficult to tell really...
Re: Yet more questions about cutting dubs...
Posted: Sun Feb 07, 2010 3:57 pm
by bobby_dozen
Bump for info about cutting the tune in my sig...
Re: Yet more questions about cutting dubs...
Posted: Sun Feb 07, 2010 4:30 pm
by pete
bobby_dozen wrote:Bump for info about cutting the tune in my sig...
Could you send a .wav snippet?
Re: Yet more questions about cutting dubs...
Posted: Sun Feb 07, 2010 4:55 pm
by Sharmaji
just in looking at that waveform, if that's the unmastered version, you're not leaving the mastering engineer much space to do his work.
if that IS the mastered version, go for it.
Re: Yet more questions about cutting dubs...
Posted: Sun Feb 07, 2010 5:24 pm
by bobby_dozen
Yeah, that's my mastered version but of course I'll take the unmastered .Wav with me. I'll up a little .Wav clip of it now, if you could have a listen pete/Sharmaji and let me know that would be wicked!
Re: Yet more questions about cutting dubs...
Posted: Sun Feb 07, 2010 5:57 pm
by honey-d
bobby_dozen wrote:Cheers for the info pete. @prisoner, I'll try calling them this week and see what happens.
Edit: The tune in my sig is one of the tunes I'm going to cut, anyone have any comments on how well it'll translate? Does it need drastic changes? I've played it out a couple of times off CD and it sounded OK but it was pretty difficult to tell really...
I unfortunately don't have much experience with vinyl, but the track is really cool!
Re: Yet more questions about cutting dubs...
Posted: Sun Feb 07, 2010 7:02 pm
by bobby_dozen
@honey-d cheers man.
Here are links to wav clips of a couple of the tracks I'm getting cut...
http://www.divshare.com/download/10406814-993
http://www.divshare.com/download/10407089-969
Cheers for helping me out people, really excited about getting some dubs cut now!
Re: Yet more questions about cutting dubs...
Posted: Mon Feb 08, 2010 9:21 pm
by bobby_dozen
Bump for knowledge on those two clips and I booked my session for next tuesday...
Re: Yet more questions about cutting dubs...
Posted: Mon Feb 08, 2010 9:53 pm
by The Phantom Banger
How much would it cost to get a dub cut?