Dubstepforum.com

-----

ah guttin man
just make a 1skinner, will probly turn out better.

I have now lost all faith in humanity.

64hz wrote:ah guttin man
just make a 1skinner, will probly turn out better.

Aiitee just rolled my first hench J filled with cheese, slighty stoned ! Man one problem, I'm getting this fucking brownish shit on the tip of the rizzla as I smoke, wtf's that?

that would be tar

solphy wrote:that would be tar

No I mean like it's wet shit on the side burns before the ash, it's like condensation shit man?

better plan: just get a pipe

Thats resin maybe you rolled to tight

if you don't know how to do your drugs, youtube is the place to be

use 3 yellow zig zags.. make sure to rip 1cm of cardboard off the packet, use this as a filter.
actually i'll stop there... if ya don't know... then ya dont know.... NIA!!


p.s. always keep ya j straight! no dolphin action! if ya wana be creative... roll up a tulip!

Right! I followed that video and made the sexiest joint i've seen! Gonna save it for tomorrow after my exam! SORTED!
Thanks guys!

Oh and another question, anyone know how to make a homemade bong? Made one before with a huge Ribena bottle but it turned out the plastic started to melt and we were taking it in FML.

Fission MONSTA wrote:Oh and another question, anyone know how to make a homemade bong? Made one before with a huge Ribena bottle but it turned out the plastic started to melt and we were taking it in FML.

Put tin foil with little holes in it over the top?

Fission MONSTA wrote:Oh and another question, anyone know how to make a homemade bong? Made one before with a huge Ribena bottle but it turned out the plastic started to melt and we were taking it in FML.

apple

this guy is a troll right?

go one step further, flip your rizla or whatever papers over so that the glue faces down.
So the blade is totally upside down with the glue pointing downwards and the glue at the bottom of the blade.
Put your bud in and roll from the bottom up.
By the time you roll once around you`ll be able to see the glue through the paper.
Lick the glue through the paper and press along the length.
Fold the rest of the paper over and tear along the line.
Add a gerrick and viola.

You have your first backward joint with only a single layer of paper the whole way round.
Use some extra thin rice rizla and you have a super thin single layer joint rather than this joint wrapped in 2 layers.
All you taste is bud, nooo paper.

As far as bongs go, get yourself a metal smoking piece.
It`s a pipe with a cup on it available from most head-shops.
Alternately guys sometimes use a piece of hose-pipe with a socket in it.
The socket acts as the cup.
This is a bit ghetto but if you can`t get a metal smoking cup and pipe it works fine.
Take a coke bottle, heat-up a hole so that it`s smaller than the pipe entering it.
Once the hole is hot and a bit smaller than the pipe, force the pipe through and the plastic will cool around the pipe.
Leaving you with an air-tight seal that doesn`t leak.

Electric_Head wrote: As far as bongs go, get yourself a metal smoking piece.
It`s a pipe with a cup on it available from most head-shops.
Alternately guys sometimes use a piece of hose-pipe with a socket in it.
The socket acts as the cup.
This is a bit ghetto but if you can`t get a metal smoking cup and pipe it works fine.
Take a coke bottle, heat-up a hole so that it`s smaller than the pipe entering it.
Once the hole is hot and a bit smaller than the pipe, force the pipe through and the plastic will cool around the pipe.
Leaving you with an air-tight seal that doesn`t leak.

Ah sweet man, just went over to Planet Bong and bought one. Dank as fuck, cheers man!

Beer can, cut a rectangle about 10cm by 10cm, roll it into a tube with a hole about 0.5cm across, put electrical tape around one end a few times, there you have a shottie tube.

Coppola wrote:...cut a rectangle about 10cm by 10cm....

Sounds suspiciously like a square ....