Popping sound on sub bass

[djfeloe]

Every time i am making a sub bass using Ableton's Operator (also with NI Massive) i get this popping sound when moving from one note to the next. ive tried putting the attack up and the release and also putting down the release but i still get this annoying popping sound.i have also messed with the length of the note but nothing. anyone else have or had this problem before? i can't figure it out and its driving me nuts

[dickman69]

u try EQ

[djfeloe]

Yep tried that as well. its weird though because this just started happening recently (would say 3-4 months) didn't have this problem the whole year

[OfficialDAPT]

Enable the glide function or make the attack time longer.

Make sure the G is lit up and set the time next to it to like 50-100 probably. Also, set the voices to 1.

[djfeloe]

ive tried that as well except turning the glide that high i usually set it to 5.59ms

[OfficialDAPT]

I made you a subbass in this ableton project file, let me know if it still pops because then it might be something else rather than ableton.
http://www.mediafire.com/?k1zkkp3srvxhe37

[djfeloe]

Alright ill check it out and let you know tomorrow

[mixedbyLUSH]

Add a little attack to Env 4, keeps it from popping. That and if you add a little release to it. Works really well for making a smoother sounding sub in massive.

[syrup]

yeah, just turn up attack/release a little

[Augment]

yeah, just turn up attack/release a little

/thread

[billy crystal meth]

smoothing out the attach fixes it for me

[Hircine]

take that filter out, you don't need to filter a pure sine wave nor eq it, then add a bit of attack and release, the pop sound will go away. You don't need to compress it either.

[drake89]

take that filter out, you don't need to filter a pure sine wave nor eq it, then add a bit of attack and release, the pop sound will go away. You don't need to compress it either.

agreed with the compression bit, but I've had this same problem. In massive I never had any luck even after changing the envelopes. So I put two low pass filters at about 100hz in ableton and I embraced the pop. After filtering it sort of sounds like a pitched 808 kick, or whatever the sub sounds like in a lot of rap songs i listen to. I like it and it works for me.

[Isley]

adjusting adsr in the synth also sometimes doesn't help. If thats the case just resample and adjust the adsr in a sampler. And make it monophonic

[Artie_Fufkin]

Use a pop filter

[syrup]

too mainstream

[djfeloe]

I made you a subbass in this ableton project file, let me know if it still pops because then it might be something else rather than ableton.
http://www.mediafire.com/?k1zkkp3srvxhe37

yo i tried it out but im still getting a slight pop after releasing a key.
Anybody else have an idea

[Gravehill]

Lowpass

[mromgwtf]

I made you a subbass in this ableton project file, let me know if it still pops because then it might be something else rather than ableton.
http://www.mediafire.com/?k1zkkp3srvxhe37

yo i tried it out but im still getting a slight pop after releasing a key.
Anybody else have an idea

Maybe that's your audio settings?
Try changing buffer size in settings.

[VirtualMark]

The problem with turning up the release of the sub, is that your sub notes can sometimes overlap if you're using lots of synths, causing a spike in the output and possible clipping or distortion. Ideally sub bass should be fairly tight and controlled as it takes up a lot of headroom.

What i do is to make my basses, duplicate the tracks and make a sine patch for each bass. Then render to audio and manually fade the ends of the sub out - this way i can both make sure there's no overlap and also get rid of any clicks.